You are on page 1of 11

Cara Membangun Pembangkit Energi

Gratis Magnetic (Romag Mini)


Posted by Ovidiu Sandru on February 6, 2008 Dikirim oleh Ovidiu Sandru pada 6 Februari 2008

Rating: 4.2/ 5 (6 votes cast) Rating: 4.2 / 5 (6 suara cast)

The Mini Romag free energy


generator from magnetic
energy uses the principle of
moving magnetic flow named
“the magnetic current” for
generating electrical power.
Mini Romag energi bebas
generator dari energi magnetik
menggunakan prinsip
pemindahan aliran magnetik
bernama "magnetik saat ini"
untuk menghasilkan tenaga
listrik. According to Magnetic
Energy this generator is able to
produce 3.5 volts, 7A DC
( about 24 Watts ) of free
electricity while its generate
sufficient power to sustain
itself… Menurut Energi Magnetik generator ini mampu menghasilkan 3,5 volt, 7A DC
(sekitar 24 Watt) listrik gratis sementara yang menghasilkan tenaga yang cukup untuk
menopang dirinya sendiri ...

This generator need to be started by an external motor during about 42 seconds at 2100
RPM. Generator ini harus dimulai dengan sebuah motor eksternal selama sekitar 42 detik
pada 2100 RPM. After this charging process, when the energy flow is established in the
Romag generator, the motor can be removed and free electrical energy can be used.
Setelah proses pengisian, ketika aliran energi yang didirikan pada generator Romag,
motor dapat dilepas dan energi listrik bebas dapat digunakan.

The Romag generator is a new revolutionary concept which generates electrical


energy without using the first flow of current generated by magnetism, it uses only the
untapped natural resource of the magnetism… Generator Romag adalah sebuah konsep
revolusioner baru yang menghasilkan energi listrik tanpa menggunakan aliran pertama
arus yang dihasilkan oleh magnet, itu hanya menggunakan sumber daya alam yang belum
dimanfaatkan dari magnet yang ...

HOW THE UNIT WORKS : CARA UNIT KARYA:


The here disclosed 3½ volt, 7 amperage magnet motor/generator must be charged up by
driving the main shaft at 2100 RPM for 42 seconds. Volt 3 ½ di sini diungkapkan, 7
ampere magnet motor / generator harus diisi oleh mengemudi poros utama pada 2100
RPM selama 42 detik. This charging process manifests as magnetic energy within the six
coils of copper wire, the copper tube supporting these coils and the copper coated steel
wires wrapped around the magnets. Hal ini memanifestasikan proses pengisian sebagai
energi magnetik dalam enam gulungan kawat tembaga, tembaga tabung ini mendukung
gulungan dan kawat tembaga baja lapis melilit magnet. This charging is accomplished
while the six coil connection wires, Part #22, are making contact and setting up their
alternating magnetic poles. pengisian Hal ini dilakukan sementara enam sambungan
kabel koil, Bagian # 22, yang membuat kontak dan setting kutub magnet bolak-balik
mereka. After the 42 second charging time one of these coil connection wires must be
opened and this circuit again completed through an energy draw at what could be called 7
amps. Setelah satu kali 42 detik pengisian dari sambungan kabel kumparan harus dibuka
dan sirkuit ini lagi diselesaikan melalui menarik energi pada apa yang bisa disebut 7
amps. See load Part #23. Lihat Bagian beban # 23. As current is drawn from the six coils,
this draw sets up magnetic poles which are a response between the rotor magnets and the
coils. Seperti saat ini diambil dari enam gulungan, menggambar ini mendirikan kutub
magnet yang merupakan respon antara magnet rotor dan kumparan. This response then
causes the main shaft to be rotated by the 12 permanent magnets as they attract and build
a release field. Respons ini kemudian menyebabkan poros utama yang akan diputar oleh
12 magnet permanen saat mereka menarik dan membangun sebuah lapangan rilis. Then
the driver unit (hand crank) is disconnected allowing the unit to rotate with the load being
the activating driving force. Kemudian unit driver (tangan engkol) diputuskan
memungkinkan unit untuk memutar dengan beban sebagai motor penggerak
mengaktifkan.

The fields of the magnets must be maintained during their spin movement. Bidang
magnet harus dipelihara selama gerakan berputar mereka. These magnetic fields which
are encapsulated are achieved by the wiring system. Ini medan magnet yang encapsulated
dicapai oleh sistem kabel. The attract/release of the magnets is a function of several
factors. Yang menarik / pembebasan magnet merupakan fungsi dari beberapa faktor.
First, the magnets attract field between north and south is completed by taking a crossing
path of attract (top of one row to bottom of next, etc.). Pertama, medan magnet menarik
antara utara dan selatan dilengkapi dengan mengambil jalur persilangan menarik (atas
satu baris ke bawah berikutnya, dll). This action has the effect of fields blending into
fields, and a hold—back attract does not happen. Tindakan ini memiliki efek medan
menyatu dengan ladang, dan memegang kembali menarik tidak terjadi. Each time a
magnet set passes a coil an interchange of like energy between the coils around the
magnets and the generating coils sets—up neutral polarities which are 'release fields' and
prevents a hold—back attract. Setiap kali melewati serangkaian magnet koil suatu
pertukaran energi seperti antara kumparan sekitar magnet dan koil menghasilkan set-up
polaritas netral yang 'bidang rilis' dan mencegah memegang kembali menarik.

One important magnetic assembly is the circuitry which allows this interchange of free
energy . Satu perakitan magnetik penting adalah sirkuit yang memungkinkan pertukaran
ini energi bebas. This is a recycling of a stabilized magnetic/electro energy not
electro/magnetic because the field of force is not a case of electrical input, an input that
created the magnetic energy, but rather a build—up of magnetic energy which caused a
free energy thrust. Ini adalah daur ulang dari sebuah / magnet elektro energi stabil tidak
elektro / magnet karena bidang gaya bukan kasus input listrik, masukan yang
menciptakan energi magnetik, melainkan membangun-up energi magnetik yang
menyebabkan energi bebas dorong.

In further defining the workings of this unit it is important to understand that although
electrical and magnetic (energy) work with similar attitudes, the manner in which they
work sets—up a differing energy effect. Dalam lebih lanjut mendefinisikan kerja unit ini
adalah penting untuk memahami bahwa meskipun listrik dan magnetik (energi) bekerja
dengan sikap yang sama, cara di mana mereka bekerja set-up efek energi yang berbeda.
One of these effects is that magnetic structures want to share their f1ow, compatible to
the Universal Force, while electrical flow argues, (short circuits, sparks, etc.). Salah satu
efek ini adalah bahwa struktur magnetik ingin berbagi f1ow mereka, yang kompatibel ke
Force Universal, sementara aliran listrik berpendapat, (arus pendek, percikan api, dll).
Because of this fact the working responses (within the unit) take place, how they are
needed, and when they are needed which results in a functioning unit. Karena fakta ini
tanggapan kerja (dalam unit) berlangsung, bagaimana mereka dibutuhkan, dan ketika
mereka dibutuhkan yang menghasilkan unit berfungsi. There is a continuous
transmutation process taking place whereby magnetic energy continually generates an
energy that manifests a measurable current. Ada proses transmutasi kontinyu terjadi
dimana energi magnetik terus menghasilkan energi yang memanifestasikan arus terukur.
PARTS LIST AND CONSTRUCTION DETAILS PARTS DAFTAR DAN DETAIL
KONSTRUKSI

When building your first unit we suggest using the stated materials. Ketika membangun
unit pertama Anda, kami menyarankan menggunakan bahan-bahan lain.

1) Aluminum Base Plate 1) Base Plate Aluminium

2) Sleave Bearing, 1″ long, ½” inside diameter, oil impregnated brass. 2) Sleave Bearing,
1 "panjang, ½" diameter, minyak kuningan diresapi.

3) 4″ long by ½” diameter Brass Shaft 3) 4 "panjang dengan ½" diameter poros Kuningan

4) Brass 2″ diameter Rotor, 1—3/4″ long 4) Brass 2 "Rotor diameter, 1-3/4" panjang
5) Six rotor slots, each 1—3/4″ long by .260 deep by 23/32″ wide. 5) Enam slot rotor,
setiap 1-3/4 "panjang dengan kedalaman 0,260 23/32" wide. These slots are spaced
exactly 60 degrees apart. Slot ini berjarak tepat 60 derajat terpisah.

6) One slot cut in center of Brass Rotor, 360 degrees around, ¼” wide by 5/16″ deep. 6)
Satu slot dipotong di tengah-tengah Kuningan Rotor, 360 derajat sekitar, ¼ "lebar 5 / 16"
deep.

7) 12 slots (formed from the six slots as the 360 degree cut is made). 7) 12 slot (dibentuk
dari enam slot sebagai cut 360 derajat dibuat). Each slot is lined with .010 thick mica
insulation. Setiap slot dilapisi dengan isolasi 0,010 mika tebal.

A total of 228 pieces of U—shaped .040 thick copper coated steel wires. Sebanyak 228
potongan berbentuk U-040 kawat baja tebal dilapisi tembaga. Each slot (Part #7) has 19
pieces of these wires fitted into the Mica, thus these wires do not contact the Brass rotor.
Setiap slot (Bagian # 7) memiliki 19 buah kabel ini dipasang ke dalam Mica, sehingga
kabel tersebut tidak menghubungi Kuningan rotor. The lead edge of these wires is flush
with the Rotor's outer surface and the trail edge protrudes 1/8″ above the Rotor's outer
diameter. Tepi memimpin kabel ini dibuat rata dengan permukaan terluar Rotor dan yang
menjorok tepi jalan 1 / 8 "di atas diameter terluar Rotor itu.

9) Eleven complete turns of .032 thick copper coated steel wire. 9) Sebelas lengkap
putaran 0,032 kawat baja tebal dilapisi tembaga. These 11 turns or 'wraps' accumulate to
3/8″ wide and the same pattern is placed around all 12 magnets. 11 ini ternyata atau
'membungkus' menumpuk untuk 3 / 8 "lebar dan pola yang sama ditempatkan sekitar
semua 12 magnet. When placed into the bent wires #8, they are a snug fit making firm
contact. Bila ditempatkan ke dalam kabel membungkuk # 8, mereka adalah cocok
nyaman membuat kontak perusahaan.

10) Are 12 pieces of .005″ thick mylar insulation inserted into the cores of the wires #9.
10) Apakah 12 lembar 0,005 "isolasi milar tebal dimasukkan ke dalam inti dari kabel # 9.
11) 12 permanent magnets, insulated with the mylar, to not contact wires # 9. 11) 12
magnet permanen, terisolasi dengan milar, untuk tidak menghubungi kawat # 9. These
magnets measure 3/4″ long, 5/8″ wide, 3/8″ thick and are made of a special composition
and strength. Magnet ini mengukur 3 / 4 "panjang, 5 / 8" wide, 3 / 8 "tebal dan terbuat
dari komposisi khusus dan kekuatan. Alnico 4, M—60; 12 AL, 28 Ni, 5 Co, bal Fe,
Isotropic permanent magnet material cooled in magnetic field, Cast 9100 TS. Alnico 4,
M-60, 12 AL, 28 Ni, 5 Co, Fe bal, Isotropik bahan magnet permanen didinginkan dalam
medan magnet, Pemain 9100 TS. 450 Brin, 2.2 Peak energy product. 450 Brin, 2.2 Peak
produk energi. When inserted in the rotor the outer faces of these 12 magnets are not to
be machined to a radius. Ketika dimasukkan pada rotor wajah luar dari 12 magnet tidak
dapat mesin untuk radius. The center of these magnets pass the center of the coils with
3/32″ clearance. Pusat magnet ini melewati pusat kumparan dengan 3 / 32 "clearance.
The edges, where the wires are wrapped, pass 1/32″ away from the coils. Tepi, mana
kabel yang dibungkus, melewati 1 / 32 "jauh dari gulungan. This 'changing magnet
spacing' aids in not only the release cycle but also contributes to rotational movement.
bantu ini 'jarak magnet berubah' tidak hanya dalam siklus rilis tetapi juga berkontribusi
terhadap gerakan rotasi. (Sharp magnet edges which are facing the coils are to be sanded
to a small smooth radius.) (Tepi magnet Sharp yang menghadapi gulungan harus
diampelas sampai radius halus kecil.)

12) Magnet polarity placement into Rotor. 12) Magnet polaritas penempatan ke Rotor.

13) Connection pattern for wires wrapped around magnets. 13) Koneksi pola untuk kawat
melilit magnet. The 12 wire wraps are divided into two sections, upper and lower of six
each. Kabel 12 wraps dibagi menjadi dua bagian, atas dan bawah dari enam masing-
masing. There are no connections between these sections. Tidak ada hubungan antara
bagian-bagian ini. The magnetic flow direction between the upper 6 wraps and the lower
6 wraps is attained by the 'flow direction' as shown in Figure 5. Arah aliran magnetik
antara 6 atas membungkus dan yang lebih rendah 6 wraps dicapai oleh 'arah aliran'
seperti yang ditunjukkan pada Gambar 5. Viewing Figure 6 shows the wires wrapped
around the magnet starting at the top 'north' half and then after 11 complete turns the wire
exits at the lower 'south' half. Melihat Gambar 6 menunjukkan kabel melilit magnet mulai
pada setengah 'utara' bagian atas dan kemudian setelah 11 selesai mengubah keluar kawat
di setengah 'selatan' rendah. As this wire then goes to the next magnet it arrives at an
attract wire which is its 'north' side. Sebagai kawat ini kemudian pergi ke magnet
berikutnya tiba di suatu menarik kawat yang berada di bagian 'utara' nya. Thus all wires
get interconnected from south to north magnet half or north to south magnet half. Jadi,
semua kabel mendapatkan saling dari selatan ke utara atau setengah magnet utara ke
selatan magnet setengah. The actual connections should be crimped copper clips not
solder with insulation tubing to prevent contact to the Rotor body. Koneksi aktual harus
klip tembaga berkerut tidak solder dengan isolasi pipa untuk mencegah kontak ke tubuh
Rotor.

14) A .030 thick copper tube (stiff material) 2″ long by 2½” inside diameter. 14) Sebuah
0,030 tabung tembaga tebal (bahan kaku) 2 "panjang dengan 2 ½" diameter.
15) Are six slots cut at the top of tube #14. 15) Apakah enam slot memotong di bagian
atas tabung # 14. These slots are 5/8″ wide by 1/32″ deep spaced at 60 degrees apart. Slot
ini adalah 5 / 8 "lebar 1 / 32" deep spasi pada suhu 60 derajat terpisah.

16) Are six slots cut at the bottom of tube #14. 16) Apakah enam slot dipotong pada
bagian bawah tabung # 14. These slots are 5/8″ wide by 5/16″ deep and in line with the
upper slots #15. Slot ini adalah 5 / 8 "lebar 5 / 16" mendalam dan sesuai dengan slot atas
# 15.

17) Six copper tube mounting points. 17) Enam tabung tembaga mounting.

18) Acrylic ring to hold Part #14, measuring 3—3/4″ OD, 2¼” ID, 3/8″ thick bolted
directly to Part #1. 18) Acrylic cincin untuk menahan Bagian # 14, mengukur 3-3/4 "OD,
2 ¼" ID, 3 / 8 "tebal bolted langsung ke Bagian # 1. This ring has a .030 wide groove cut
¼”deep to allow the six copper tube mounting points, Part #17, to be inserted. Cincin ini
memiliki alur 0,030 ¼ potong lebar "mendalam untuk mengizinkan pemasangan pipa
tembaga enam poin, Bagian # 17, untuk dimasukkan.

19) A .002″ thick plastic insulation paper to be placed around the inside and outside of
Part #14. 19) Sebuah 0,002 "kertas tebal isolasi plastik untuk ditempatkan di bagian
dalam dan luar Bagian # 14.

20) Are six coils of insulated copper wire, each coil having 72 turns of .014 thick wire.
20) Apakah enam gulungan kawat tembaga, masing-masing coil memiliki 72 putaran
0,014 kawat tebal. Each coil is wound with two layers, the bottom layer to completely fill
the 5/8″ wide slot with 45 turns and the top layer to span 5/16″ wide with 27 turns. Setiap
kumparan luka dengan dua lapisan, lapisan bawah untuk sepenuhnya mengisi 5 / 8 "slot
lebar dengan 45 berbalik dan lapisan atas rentang 5 / 16" wide dengan 27 bergantian. To
be sure each coil has the exact wire length or 72 turns, a sample length wire is wrapped
then unwound to serve as a template for six lengths. Untuk memastikan kumparan
masing-masing memiliki panjang kawat tepat atau 72 berubah, kawat panjang sampel
dibungkus kemudian dibatalkan untuk melayani sebagai template untuk enam panjang. A
suggested coil winding method is to fill a small spool with one length then by holding the
copper tube at the lower extension, then start at the plus wire in Figure 2 and temporarily
secure this wire to the outer surface of the tube. Sebuah kumparan belitan disarankan
metode untuk mengisi spool kecil dengan satu panjang kemudian dengan memegang
tabung tembaga di ekstensi lebih rendah, maka mulai dari kawat ditambah pada Gambar
2 dan untuk sementara aman kawat ini ke permukaan luar tabung. Next, place the pre—
measured spool of wire inside the tube, wrapping down and around the outside advancing
clockwise until the 5/8″ slot is filled with 45 turns. Selanjutnya, tempat spool pra-diukur
dari kawat di dalam tabung, membungkus bawah dan sekitar searah jarum jam maju luar
sampai 5 / 8 "slot diisi dengan 45 bergantian. Then, return this wire back across the top of
the coil for 15/32″ and winding in the same direction again advance clock—wise placing
the second layer spanned for 5/16″ with 27 turns. Kemudian, kembali kawat ini kembali
di bagian atas kumparan untuk 15/32 "dan berliku dalam arah yang sama lagi muka jam-
bijaksana menempatkan lapisan kedua berlangsung selama 5 / 16" dengan 27 berubah.
This method should have the second layer perfectly centered above the first layer.
Metode ini harus memiliki lapisan kedua sempurna berpusat di atas lapisan pertama.
After winding this coil, repeat the process by again filling the small spool with another
length of pre—measured wire. Setelah berkelok-kelok koil ini, ulangi proses dengan
kembali mengisi spool kecil dengan panjang kawat lain pra-diukur. A very important
magnetic response happens as all six coils have their second layers spaced as disclosed.
Respon magnetik yang sangat penting terjadi karena semua enam gulungan memiliki
lapisan kedua mereka spasi seperti yang diungkapkan.

21) This number identifies the top view of the second layer. 21) Jumlah ini
mengidentifikasi pandangan atas lapisan kedua.

22) Connection pattern for six coils. 22) Koneksi pola untuk enam gulungan. When the
unit is driven at start—up (hand crank) for 42 seconds at 2100 RPM, all six jumper wires
must be together which means the plus wire goes to the minus wire connected by the start
switch. Saat unit didorong saat start-up (tangan engkol) selama 42 detik pada 2100 RPM,
semua enam kabel jumper harus bersama-sama yang berarti kawat ditambah pergi ke
kawat minus dihubungkan oleh saklar mulai. After 42 seconds the load is added to the
circuit and the start switch is opened. Setelah 42 detik beban ditambahkan ke sirkuit dan
saklar mulai dibuka. To double check your connections between the coils, note that the
finish wire of coil #1 goes to the finish wire of coil #2, which is top layer to top layer.
Untuk mengecek koneksi Anda antara kumparan, perhatikan bahwa kabel akhir dari
kumparan # 1 pergi ke kawat akhir dari kumparan # 2, yang lapisan atas ke lapisan atas.
This pattern then has start of coil 2 (bottom layer) going to start of coil 3 (also bottom
layer). Pola ini kemudian memiliki awal coil 2 (lapisan bawah) akan mulai dari koil 3
(juga lapisan bawah). When the copper tube with the coils is placed around the rotor, the
distance from any magnet to any coil must be identical. Ketika tabung tembaga dengan
kumparan ditempatkan sekitar rotor, jarak dari magnet apa pun untuk koil pun harus
identik. If it measures different, acrylic holding shapes can be bolted to the aluminum
base, protruding upward, and thus push the copper tube in the direction needed to
maintain the spacing as stated. Jika ukuran yang berbeda, bentuk memegang akrilik dapat
melesat ke dasar aluminium, menonjol ke atas, dan dengan demikian mendorong tabung
tembaga dalam arah yang dibutuhkan untuk menjaga jarak yang dinyatakan.

23) Wires to load. 23) Kabel untuk me-load.

24) Wires to start switch. 24) Kabel untuk mulai beralih.

25) Rotational direction which is clock—wise when viewing from top down. 25) arah
putaran yang searah jarum jam saat melihat dari atas ke bawah.

26) Acrylic dome for protection against elements. 26) Acrylic kubah untuk perlindungan
terhadap elemen.

27) Coating of clear acrylic to solidify rotor. 27) Coating dari akrilik yang jelas untuk
memperkuat rotor. Do not use standard motor varnish. Jangan menggunakan motor
standar pernis. Pre-heat the rotor and then dip it into heated liquid acrylic. Pra-panas rotor
dan kemudian celupkan ke dalam akrilik cair dipanaskan. After removal from dip tank,
hand rotate until the acrylic hardens, then balance rotor. Setelah penghapusan dari tangki
dip, tangan memutar sampai mengeras akrilik, saldo rotor. For balancing procedure,
either add brass weights or remove brass as needed by drilling small holes into rotor on
its heavy side. Untuk prosedur balancing, baik menambah bobot kuningan atau
menghapus kuningan yang diperlukan oleh pengeboran lubang kecil ke rotor pada sisi
yang berat.

28) Insulation tubing on all connections. 28) Isolasi tubing pada semua sambungan.

29) Shaft for start purposes and speed testing (if desired). 29) poros untuk tujuan
pengujian awal dan kecepatan (jika diinginkan).

This concludes the parts list for the Mini-Romag. Hal ini menyimpulkan daftar suku
cadang untuk Mini-Romag.

This simple unit demonstrates profound concepts and has a surprising number of
applications. Unit ini menunjukkan konsep sederhana mendalam dan memiliki sejumlah
aplikasi mengejutkan. Remember, it must have a load to work, something that attracts
magnetic energy. Ingat, ia harus memiliki beban untuk bekerja, sesuatu yang menarik
energi magnetik. Build this unit and explore new possibilities of creating “free energy”
yourself! Membangun unit ini dan mengeksplorasi kemungkinan-kemungkinan baru
untuk menciptakan "energi bebas" sendiri!

Read more: http://www.greenoptimistic.com/2008/02/06/how-to-build-a-free-magnetic-


energy-generator-mini-romag/#ixzz1IXiIZZxc

You might also like